How to make a track?
Posted Jan 31 2019 - 05:11 AM
When hsv file is shorter than track, aren't final sections in black?
Posted Jun 29 2019 - 09:54 AM
099.jpg 28.89K 40 downloads
The ads have to match the inclination of the track, and for that is the 8th value of the lines of the TSO file, but it only works for me in 10-15% of cases. Is it my fault or is it not working well?
I'm doing diferent 3dos for places with diferent inclination, but would be better not to duplicate them...
Posted Jun 29 2019 - 10:03 AM
if you use obj, it should work all the time.
PS: if you don't do it already, use 3dsimed to check your result and fine tune it.
Posted Jun 29 2019 - 02:40 PM
Unfortunately, I need the "objl". The difference can be seen here:
delante0.jpg 25.24K 29 downloads delante1.jpg 25.1K 32 downloads
The good thing is that there are only a little amount of ads in slopes that must be inclined.
Despite the use of "objl", backwards is almost impossible to get a no corrupted view.
atras1.jpg 23.8K 25 downloads
Is there any trick to avoid the intrusion of the fences? Am I missing something?
Posted Jun 29 2019 - 03:13 PM
That usually happens if the 3do crosses or even only touches a vertical wall.
If you are trying to apply a 3do in a curved section, you can divide the single object into smaller ones that together make the whole object.
Every single smaller object must fit into one single subsection that you can see very well in 3dsimed.
I usually then use scaled down 3dos in the build folder so they are easier to place inside a subsection when compiling; then in GPL folder I use 3dos that can touch or even cross the subsection and that does not matter since the track.3DO has been compiled with 3dos that fit in their own single subsection.
Is this in some ways understandable to you?
Sometimes is just easier to draw a texture to be used in the GTK that covers the whole section (unk4= 8) with the ads you want painted on top of the fence.
Posted Jun 29 2019 - 04:11 PM
I began to think about divide an ads but it was an inclined one, wich makes the job little more difficult. I keep the ads without crossing any wall, but transversal lines are another question.
It has no sense to make anything now, as there must be all the ads in place and in final size and then see what is needed as now are continuously moving.... I'll keep in mind all what you say. Thanks again!
Edited by quico, Jun 29 2019 - 04:12 PM.
Posted Jun 30 2019 - 03:54 AM
Is this in some ways understandable to you?
I understand that you have a scaled 3do to build the track.3do, and a big one in the gpl track folder??? Yesterday I didn't realize what you mean (if I'm right, as my english is so unsafe). Cheating GPL!!!
Posted Jun 30 2019 - 07:14 AM
Then another one that is shorter so it fits safely in the section (or subsection for the curved sections) to cheat the compiling program in the folder that you use to compile the track.3DO
In this way I did for example the Les Combes barrier; made of many little 3do objects with collision (everyone sitting in their subsection) instead of a single one that would have clip everywhere. You can check that.
Posted Dec 27 2019 - 12:57 PM
errorRpy2Lp.jpg 12.71K 11 downloads
and... MERRY CHISTMAS!
Edit: Revised version of the program, I have seen that did not have the most up-to-date, which is that of the corresponding thread.: http://srmz.net/inde...?showtopic=2990
Now it works perfectly.
Edited by quico, Dec 27 2019 - 04:35 PM.
Posted Dec 29 2019 - 02:14 PM
polys01.jpg 80K 6 downloads
changing scale B from 10 to 34, the amount of polys decreases dramatically (8000), but in the report of the
polys03.jpg 49.7K 4 downloads
Also changing 7th value, section resolution in turns, works badly as I can only get turns with 2, 4 or 8 subsections, although this is a quick evaluation. Perhaps only 2 multipliers?
Really lost with things I thought was simpler, but coulld be so interesting to reduce the load of polys. Any help?
Have checked the size of the mytrack.3do, and it changes in accordance with the changes in the set file.
Edited by quico, Dec 31 2019 - 10:44 AM.
Posted Dec 29 2019 - 03:41 PM
The 1st and 2nd values go together and determine the limits of how long the subsections will be.
With 3rd 4th and 5th you determine how long the subsections will be (in the graphic part, the 3DO) so if the track is flat, you use high numbers while for elevations that changes a lot you will need to use lower numbers to avoid cars fly or sink above below the asphalt surface.
example for flat track (Monza ):
43.0 125.0 43 84 125 15.0 0.03125 1000 1000 100
example for wavy track (Road America ):
60.0 120.0 20.0 20.0 20.0 20.0 0.03 1000 1000 100
Posted Dec 30 2019 - 11:18 AM
7th value have an easy behaviour, except for that lack of elasticity that makes changes only of 2, 4, 8... and that changes can be seen both in trk23dow and
But when 4th value is changed, in trk23dow I get a decrease of polys, and the 3do file also changes the same direction. But when edited in
I use to control the elevation changes with unk4, so it could be that there are no variations in the track, but 8000 polys are so much polys not to see nothing at all. I want to know if there is a real improvement in that drop of polys that will became a better frame rate although they are invisible.
From where have been removed those polygons?
Edited by quico, Dec 31 2019 - 10:43 AM.
Posted Dec 30 2019 - 01:09 PM
are these parameters related with the angles in the inside of the track?
I noted that the inside line of the corners are seen as straights connected by angles, which is more noticeable in some tracks than in others. In Alta Gracia I left those parameters as received from Juha and I noted the inside of the track has somewhat long "sections", instead of a smooth curved line.
I'm wondering if I could have solved it tweaking these parameters...
Cheers and thanks; Marcos
Posted Dec 30 2019 - 01:23 PM
As I was talking above, that number seems to be limited to 2, 4, 8... As Gineto said, the lower the value in set file, the more subsections.
Of course you can change the number of subsections also with unk4, that works the same in corners than in straight sections.
But you will never get a curved line, only many straight lines connected.
Edited by quico, Dec 30 2019 - 03:14 PM.
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users